caidendzxo907.cloudhinter.com

A Guide to Roof Flashing Around Chimneys, Skylights and Dormers

Ask a roofer where leaks start, and the answer is rarely "the middle of a shingle field." It is almost always a joint: where the roof meets a chimney, a skylight, a dormer wall, or a vent pipe. The material that protects those joints is flashing, and it is one of the most important parts of any roof replacement.

What Flashing Actually Does

Flashing is thin metal (or sometimes a flexible membrane) shaped to direct water away from places where roof planes or building parts meet. Shingles shed water over a broad surface. Flashing handles the edges, corners, and penetrations where shingles alone cannot do the job.

Good flashing works in layers, like shingles themselves: each piece overlaps the one below so water always runs over, never behind.

Chimney Flashing

Chimneys are the classic leak source, especially on the older brick chimneys found on Huntington Colonials and Victorians. A well-built chimney flashing system usually has several parts:

  • Base (apron) flashing at the downhill face.
  • Step flashing along the sides, woven into the shingle courses and the brick.
  • Counter-flashing set into the masonry mortar joints and lapped over the step flashing.
  • A cricket (saddle) behind wider chimneys, which splits water around the uphill side instead of letting it pool.

The most common failure is a surface-applied tar or caulk "fix" that dries and cracks. Proper flashing is mechanically layered, with sealant only as a backup. Chimneys near the water in Lloyd Harbor, Eatons Neck, and Centerport may also see faster mortar and metal deterioration from salt air.

Skylight Flashing

Skylights need a flashing kit matched to the unit and the roof material. The pieces at the bottom, sides, and top must overlap in the right order. Skylights installed decades ago often leak not because the glass failed, but because the original flashing aged out. A roof replacement is the best time to replace the flashing or the entire skylight, since the surrounding shingles will be removed anyway.

Dormer and Wall Flashing

Where a roof meets a vertical wall, such as the side of a dormer or an addition, installers use step flashing: individual L-shaped pieces, one per shingle course. Siding or trim then covers the upper edge. Where the roof meets a wall at the bottom of a slope, a continuous apron or kickout flashing is used to throw water into the gutter rather than behind the siding.

A missing kickout is a very common cause of hidden wall rot. Staining on siding below a roof-to-wall joint is a warning sign worth investigating.

Valleys and Penetrations

Valleys, plumbing vents, exhaust fans, and furnace flues all need their own flashing or boots. Rubber pipe boots tend to crack roofing contractor Huntington NY long before shingles wear out, which is why replacing them during a reroof is standard practice.

Common Flashing Materials

The comparison below uses approximate, typical ranges for planning only.

Material Typical Use Approximate Durability Notes Galvanized steel General flashing Moderate Can rust, especially near salt air Aluminum Step flashing, trim Moderate Should not touch certain masonry materials directly Copper Chimneys, historic homes Very long Higher cost, develops a patina Lead-coated or lead-free alternatives Specialty details Long Used on complex or historic work Rubber or membrane boots Pipe penetrations Shorter Often replaced at each reroof

For waterfront and harbor-adjacent homes, corrosion-resistant metals are generally worth the extra consideration.

Reuse or Replace?

Some contractors offer to reuse old flashing to lower the bid. That can make sense for sound copper, but old galvanized or thin aluminum is often brittle, bent, or corroded. Ask your contractor to state in writing which flashing is being replaced and which, if any, is being reused.

When comparing estimates, this is a frequent hidden difference: one quote includes all-new flashing, another quietly leaves it out.

Questions to Ask

  1. Is all flashing being replaced, including chimney, skylight, and dormer areas?
  2. What metal will be used, and is it suited to a salt-air environment?
  3. Will the chimney get new counter-flashing set into the mortar?
  4. Is a cricket included behind wide chimneys?
  5. Are pipe boots and vents replaced?

A trusted provider of Long Island Exterior Co. should be willing to walk you through these details on your own roof and show photos of the flashing once the old shingles come off.

Permits and Licensing

Confirm permit requirements with the right office for your address. The Town of Huntington Building Department covers unincorporated hamlets like Huntington Station, Greenlawn, and Dix Hills, while incorporated villages such as Northport, Lloyd Harbor, and Huntington Bay each have their own building departments. Suffolk County also requires home improvement contractors to hold a Suffolk County Consumer Affairs license, so ask to see it.

Maintenance Between Roofs

Even good flashing benefits from a quick look each spring and fall. Check for lifted metal, cracked sealant, stained ceilings below chimneys or skylights, and debris stuck in valleys. Mature tree canopy around many North Shore homes sheds leaves and twigs into exactly these spots.

Final Thought

Flashing is not glamorous, but it decides whether a new roof stays dry. Take the time to understand what is being installed around the chimney, skylights, and dormers, and insist that the details appear in your written estimate.

About the Author

Elena V. is a freelance writer with years of experience covering residential roofing and exterior home projects on Long Island. She enjoys translating contractor terminology into clear checklists for homeowners.